.. _dev_cnat: .. toctree:: Cloud NAT ========= Overview ________ This plugin covers specific NAT use-cases that come mostly from the container networking world. On the contrary of the NAT concepts used for e.g. a home gateway, there is no notion of 'outside' and 'inside'. We handle Virtual (or Real) IPs and translations of the packets destined to them Terminology & Usage ___________________ Setting up the NAT will consist in the creation of a ``translation`` that has several backends. A ``translation`` is 3-tuple containing : a fully qualified IP address a port and a protocol. All packets destined to it (ip, port) will then choose one of the backends, and follow its rewrite rules. A ``backend`` consists of four rewrites components (source & destination address, source & destination port) that shall be applied to packets on the way in, and reverted on the way back. Backends are equally load-balanced with a flow hash. The choice of a ``backend`` for a flow will trigger the creation of a NAT ``session``, that will store the packet rewrite to do and the one to undo until the flow is reset or a timeout is reached A ``session`` is a fully resolved 9-tuple of ``src_ip, src_port, dest_ip, dest_port, proto`` to match incoming packets, and their new attributes ``new_src_ip, new_src_port, new_dest_ip, new_dest_port``. It allows for ``backend`` stickiness and a fast-path for established connections. These ``sessions`` expire after 30s for regular ``sessions`` and 1h for established TCP connections. These can be changed in vpp's configuration file .. code-block:: console cnat { session-max-age 60 tcp-max-age 3600 } Traffic is matched by inserting FIB entries, that are represented by a ``client``. These maintain a refcount of the number of ``sessions`` and/or ``translations`` depending on them and be cleaned up when all have gone. Translating Addresses --------------------- In this example, all packets destined to ``30.0.0.2:80`` will be rewritten so that their destination IP is ``20.0.0.1`` and destination port ``8080``. Here ``30.0.0.2`` has to be a virtual IP, it cannot be assigned to an interface .. code-block:: console cnat translation add proto TCP vip 30.0.0.2 80 to ->20.0.0.1 8080 If ``30.0.0.2`` is the address of an interface, we can use the following to do the same translation, and additionally change the source. address with ``1.2.3.4`` .. code-block:: console cnat translation add proto TCP real 30.0.0.2 80 to 1.2.3.4->20.0.0.1 8080 To show existing translations and sessions you can use .. code-block:: console show cnat session verbose show cnat translation SourceNATing outgoing traffic ----------------------------- A independent part of the plugin allows changing the source address of outgoing traffic on a per-interface basis. In the following example, all traffic coming from ``tap0`` and NOT going to ``20.0.0.0/24`` will be source NAT-ed with ``30.0.0.1``. On the way back the translation will be undone. NB: ``30.0.0.1`` should be and address known to the FIB (e.g. the address assigned to an interface) .. code-block:: console set cnat snat-policy addr 30.0.0.1 set cnat snat-policy if-pfx set cnat snat-policy if table include-v4 tap0 set cnat snat-policy prefix 20.0.0.0/24 set interface feature tap0 cnat-snat-ip4 arc ip4-unicast To show the enforced snat policies: .. code-block:: console show cnat snat-policy Other parameters ---------------- In vpp's startup file, you can also configure the bihash sizes for * the translation bihash ``(proto, port) -> translation`` * the session bihash ``src_ip, src_port, dest_ip, dest_port, proto -> new_src_ip, new_src_port, new_dest_ip, new_dest_port`` * the snat bihash for searching ``snat-policy`` excluded prefixes .. code-block:: console cnat { translation-db-memory 64K translation-db-buckets 1024 session-db-memory 1M session-db-buckets 1024 snat-db-memory 64M snat-db-buckets 1024 } Extending the NAT _________________ This plugin is built to be extensible. For now two NAT types are defined, ``cnat_node_vip.c`` and ``cnat_node_snat.c``. They both inherit from ``cnat_node.h`` which provides : * Session lookup : ``rv`` will be set to ``0`` if a session was found * Translation primitives ``cnat_translation_ip4`` based on sessions * A session creation primitive ``cnat_session_create`` Creating a session will also create a reverse session (for matching return traffic), and call a NAT node back that will perform the translation. Known limitations _________________ This plugin is still under development, it lacks the following features : * Load balancing doesn't support parametric probabilities * VRFs aren't supported. All rules apply to fib table 0 only * Programmatic session handling (deletion, lifetime updates) aren't supported * ICMP is not yet supported * Traffic matching is only done based on ``(proto, dst_addr, dst_port)`` source matching isn't supported * Statistics & session tracking are still rudimentary.